The PDF is here: Document 90000253E as-of Sept-2009. In broadcast automation the Video Disk Control Protocol (VDCP) use the 9-Pin Protocol to playout broadcast programming schedules. Digi Support has an official document that covers EIA-232/422/485 in general, which is document 90000253 and titled Cable Guide Including all PortServer TS, Digi Connect, and Digi One Products. ![]() This is done by setting bits in the OTP memory of the SoC. The Raspberry Pi can be configured to allow the boot mode to be selected at power on using hardware attached to the GPIO connector: this is GPIO boot mode. Just hook up an rca to the composite pins and you have yourself a cable. GPIO boot mode is only available on the Raspberry Pi 3A+, 3B, 3B+, Compute Module 3 and 3+. N Some systems may require a male to male adapter. 9 Ring Indicator (RI) Input A wiring diagram is shown below. Leadtek TV-OUT (6 pin) Pinout of the PS/2 connector used on some Leadtek and VisionTek GeForce2 Ti cards as tvout connectors. However its simple way to perform troubleshooting means it will stay around for a long time. Contact closure momentarily shorts an inputs pin on a remote connector to ground. In the new millennium, RS-422 is slowly phased out in favor of Ethernet for control functions. This 9-pin RS-422 pinout has become a de facto standard, used by most brands in the broadcast industry. Many modern hard disk recorders and solid-state drive recorders can still emulate a 1982 Sony BVW-75 Betacam tape recorder. Editing machines relied heavily on the 9-Pin Protocol to remotely control automatic players and recorders. While nowadays all post-production editing is done with a non-linear editing system, in those days editing was done linearly, using online editing. ![]() It uses an DE-9 D-Sub connector with 9 pins (hence the name), where bi-directional communication takes place over a four wire cable according to the RS-422 standard. By default, TRST is not connected, but the Cortex-M Adapter comes with a. The 9-Pin Cortex-M Adapter may also be used to connect J-Link or Flasher to a non-Cortex-M target as far as the target connector uses the same pinout as shown below. Sony introduced this protocol to control reel-to-reel type C video tape recorders (VTR) as well as videocassette recorders (VCR). It adapts from the 20-pin 0.1'' JTAG connector to a 9-pin 0.05'' Samtec FTSH connector as defined by Arm. If anyone has the pinout, that would be great - Will at least allow me to make an adapter until the backordered one comes in.The Sony 9-Pin Protocol or P1 protocol is a two-way communications protocol to control advanced video recorders. Ive bought about a half dozen motorsthat use the above scheme, and the wires were as shown. I'm $6k in for their electronics and can't get the boat in the water. This is the usual pin out for the 9 pin Julet connector, View attachment 255643 Most motors have the male pins coming out of the motor, so the connector will fit thru a 12mm axle nut, makes for easier maintenance. I have already looked at adding another glassed in transducer, but the area is totally inaccessible (hence why the do them at the factory). Humminbird says they do not have that either (not sure how they designed the adapter cable if that is true).ĭoes anyone know the pinout for the 14-pin transducer connector? I have searched the internet high and low and cannot find the pinout for the 14-pin transducer connector coming out of the Solix (or Y-cable). ![]() The connector for the thru-hull only has 2 pins on it (9 spots, but only 2 pins present). I talked to someone at Humminbird and they said they had some, but then sent me the wrong part (glad I paid for express shipping). Have tried ordering 3 places and they all contact me afterward saying they cannot get it. I have the Y-cable, but the AD 1429 cable needed to go from the 9-pin to the 14-pin is on backorder everywhere. Ranger decided to put an old-style thru-hull transducer with the 9-pin connector in the new boat. Just got a new boat and added 2 Solix 12s.
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |